Airmada AirJet Shower Drying System
The AirJet Shower Drying System uses air to solve a common problem — wet and moldy showers. Mold and mildew lose their breeding ground. All you do is flip the timer-controlled switch and walk away.
Learn More About the AirJet Shower Drying System
Simplicity in the shower,
after the shower.
Everyone talks about the shower, the water jets, the rain head, etc. But what about when the shower ends and it needs to dry? That’s where we come in – your showers’ new best friend, the AIRMADA AirJet Shower Drying System.
It’s the perfect anecdote and a must-have for every steam shower. Eliminate the steam and humidity. While less than 2” in diameter, the strategically placed jets gently dry the floor and shower compartment — simply, quickly, beautifully.
The AirJet helps dries your shower in minutes... not hours.
The typical shower takes 5 to 7 hours to dry. The AirJet Shower Drying System significantly reduces that drying time!
The AirJet System is built directly into the ceiling and walls of your shower. Depending on the size of your shower space, four to twenty threaded AirJet nozzles set flush to the shower surface. A hidden-behind-the-walls three-quarter-inch I.D. hose connects to each of the nozzles and then goes to a manifold, which is hooked to AIRMADA's AirMax Whisper blower with 2-inch plumbing. The AirMax Whisper blower can be located virtually anywhere up to 50 feet from the shower.
The AIRMADA system is clean and simple. It uses just air to solve a problem — wet and moldy showers — which in the past has required ongoing diligence with a squeegee, towel drying and harsh chemicals. Finally there's an opportunity to break the mold and stave off the repercussions of wet showers with jet-powered air from AIRMADA!
Designer Nozzles To Elevate Your Shower
AirJet Shower Drying System Nozzles are available in eight designer finishes and both directional and non-directional nozzles based on application.
AirJet Shower Drying System Lookbook
FAQs
Airmada Air Jet Shower Drying System
No. You still need to regularly clean your shower. Our system works to prevent mold and mildew from happening in the first place, which will reduce or eliminate the need for harsh chemicals and make the space easier to clean.
You will always want a bathroom fan. The AirJet system brings air into the space to dry the surfaces, and the bathroom fan then works to remove that air.
This system can be used in dog baths, above mirrors, low on the wall to dry areas near a bathtub, in a wet room, mud room, outdoor shower, gyms, spas, hotels, and any other area that is prone to moisture issues or slippery surfaces. Our system can also be used above windows that tend to gather condensation.
It really depends on the environment and the water in your area. For perfect glass we suggest ordering the AirPocket Door. We always recommend a protective treatment/coating on the glass, and for areas of hard water, using a water softener for optimal glass results. For most people that want perfect looking glass, periodic squeegeeing is necessary.
We custom design each AirJet Shower Drying System to individually fit your exact space and needs. We focus air on the walls, floor, benches and ceiling (steam shower application) Please contact your local showroom or fill out our online estimate form for details.
For showers with ceilings over 10’ or for areas where the space above the shower cannot be accessed, we use vertical nozzle placement.
It is best installed at rough in, after plumbing. Rough in nozzle bases are attached to framing and the manifold is attached to the framing above the shower space. See our step-by-step installation manual for more info.
Your custom layout includes a drawing that will come with your AirJet Shower Drying System. Our team is always available to assist during install.
The motor can be installed up to 50’ from the shower in a conditioned space within the house, that way it is not bringing in humidity or cold air. Good locations are mechanical room, conditioned space in a garage, laundry room, closet, finished attic, or cupboard. The blower draws air from around it, so it needs to be placed in a large enough space to take in air from around it. The motor needs to be accessible in case it needs to be serviced. Always follow your local codes for HVAC appliances in spaces. Some insulation material is not appropriate around mechanical HVAC devices.
You can plumb as far as 50 feet away. If your job requires it to be farther, we recommend contacting us to discuss it further.
Sometimes the selection of finish surfaces can change after the rough in nozzles are installed. We sell extended nozzle trim. Contact us for details
All shower drying systems come with a relay which is installed near the blower motor. The relay allows you to swap out the timer switch.
Related products
-
Xtreme Mats Under Sink Cabinet Mats
SHOP NOWOur under sink cabinet mats are perfectly sized for kitchen, bathroom, and laundry room cabinets. From spills...
-
Komuso Shift
$85.00 SHOP NOWThe Shift helps you quickly and easily combat anxiety by slowing your breathing. It’s a...
-
Mindbodygreen Clean Coffee+
$26.00 SHOP NOW100% whole bean organic coffee • high in antioxidant polyphenols† • third-party tested for mold†...